Important Plumbing Insights for Bathtub Installation
Important Plumbing Insights for Bathtub Installation
Blog Article
We have stumbled on the article about A Step-by-Step Guide to Installing a Bathtub listed below on the web and accepted it made sense to talk about it with you on this page.
Mounting a bath tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and also occasionally, tiling skills. Changing an old tub with a new one is likewise a reasonably hard job. If the old bathtub is readily easily accessible, the task can relocate easily; if you have to open up a wall to remove the old tub and also position the new bathtub, the task is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and also embeded in the brand-new one. See to it you have actually certified yourself for the job and also fit trying it. Instead of employing a service provider to take over a halfway-completed job, it is much better to consider utilizing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This write-up will help you install a brand-new tub in your restroom if you have actually already purchased a brand-new tub and also don't need to alter the plan of your previous water system pipelines.
Your tools as well as product checklist ought to comprise the following:
Getting ready for the Setup
Firstly, the sustaining structure provided with the bath ought to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to see to it that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets device to prevent stress on the bathtub.
Fit the versatile faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you use all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather bothersome because of the limited access that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will originate from the pipelines. As soon as the supply pipes have actually been removed, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 tiny points.
The next goal is to make certain that the tub is leveled all round. This can be attained by inspecting the spirit level and changing the feet on the bath tub until the spirit level reads level.
To mount taps, fit all-time low of the furthest flexible faucet connector to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
Activate the water supply and check all joints and new pipework for leaks as well as tighten them if essential. Load the bathtub as well as additionally inspect the overflow electrical outlet as well as the normal outlet for leaks.
Ultimately, repair the bath paneling as explained in the supplier's instruction manual. Tiling and securing around the tub should wait until the bathtub has actually been made use of at least when as this will certainly resolve it into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin ensuring that the washing machines remain in area in between the tap and also the sink. Protect the faucet in place with the producer given backnut. When the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former kind must be attached to the tap finishes first, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack an inflexible seal, creating the water to permeate the wall in between the bath as well as the tiling, causing complications with wetness and also possible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, as well as are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water before securing, to allow for the motion experienced when the tub remains in use. The sealer can crack rather very early if you do not consider this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily offered on the market. It is recommended to fit the tiles making use of water-resistant or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about A Step-by-Step Guide to Installing a Bathtub? Make feedback further down. We will be pleased to find out your opinion about this page. We hope that you come back again in the future. If you please take the time to share this article if you enjoyed it. We take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Source This Article Report this page